LORO-X Bends

Direction changes and offset pipe dimensions

PDF excerpt from rainwater standpipe brochure

Offset pipe dimensions when using 2 LORO bends

DIN 1986-100 6.1.6 regulates for gravity flow: "Direction changes of underground or collecting pipes may only be made with bends ≤ 45°.". For measured or calculated drainage systems, the performance certificates of the manufacturers apply.

The attached PDF lists the offset pipe dimensions when using the following LORO-X bends:

1. LORO-X Bends (hot-dip galvanised and coated steel)
2. LORO-XCL Bends (stainless steel)
3. LORO-N Bends (copper)

LORO-X Bends

When using anchor clips on the spigot end of the bend, the variant with notch must be used in some cases.

LORO-X Bends
	DN 32	DN 40	DN 50	DN 70	DN 80	DN 100	DN 125	DN 150	DN 200
87°	00300.032X	00300.040X	00300.050X	00300.070X	00300.080X	00300.100X	00300.125X	00300.150X	00300.200X
70°		00310.040X	00310.050X	00310.070X	00310.080X	00310.100X	00310.125X	00310.150X	00310.200X
45°	00320.032X	00320.040X	00320.050X	00320.070X	00320.080X	00320.100X	00320.125X	00320.150X	00320.200X
30°	00330.032X	00330.040X	00330.050X	00330.070X	00330.080X	00330.100X	00330.125X	00330.150X	00330.200X
15°	00340.032X	00340.040X	00340.050X	00340.070X	00340.080X	00340.100X	00340.125X	00340.150X	00340.200X

LORO-X Bends with tight radius

LORO-X SHORT RADIUS BEND 87 DEGREES DN 70

LORO-X Bends with tightradius
	DN 40	DN 50	DN 70	DN 80
87°	00350.040X	00350.050X	00350.070X	00350.080X
45°	00352.040X	00352.050X	00352.070X

LORO-X Bend 87 degrees with extended outlet 119 mm DN 100

LORO-X Bend withextended outlet 119 mm
	DN 100
	00306.100X

LORO-X Bend 87 degrees with extended outlet 99 mm DN 100

LORO-X Bend withextended outlet 119 mm
	DN 100
	00304.100X

LORO-X Bend with calming section

LORO-X Bend withcalming section
	DN 100
	03521.100X

LORO-X Offset bends (offset pipe, plinth angle)

Due to the offset, the offset bend is ideally suited for downpipes to bridge wall and plaster projections, for example.

LORO-X Offset pipes (offset bends)
	DN 50	DN 70	DN 80	DN 100	DN 125
200 mm	00380.050X	00380.070X	00380.080X	00380.100X	00380.125X
130 mm	00390.050X	00390.070X	00390.080X	00390.100X	00390.125X
75 mm	00400.050X	00400.070X	00400.080X	00400.100X	00400.125X

LORO-X Pipe compensation DN 70/125/70 axial compensation 60 mm

LORO-X PIPE COMPENSATOR DN 70/125/70 AXIAL COMPENSATION 60 MM

LORO-X Pipe compensation DN 70/125/70
axial compensation	DN 70/125/70
60 mm	00400.CECX

LORO-X Angle bend 90 degrees with standard socket

LORO-X ANGLE BEND WITH STANDARD SOCKET DN 40

LORO-X Angle bend 90°,with standard socket
	DN 40	DN 50	DN 70	DN 80	DN 100
90°	00500.040X	00500.050X	00500.070X	00500.080X	00500.100X

LORO-X Angle bend 90 degrees with short socket

LORO-X ANGLE BEND WITH SHORT SOCKET DN 50

LORO-X angle bend 90°, with short socket
	DN 40	DN 50	DN 70	DN 80	DN 100
90°	00510.040X	00510.050X

LORO-X Angle bend 90 degrees reduced with standard socket

LORO-X REDUCING ANGLE BEND WITH STANDARD SOCKET, DN 50/40

LORO-X Angle bend 90°,reduced with standard socket
	DN 50/40	DN 70/50
90°	00501.BA0X	00501.CB0X

LORO-X Bend - Pipe in pipe -

LORO-X DOUBLE PIPE BEND 87 DEGREES, DN100/50 FOR MAIN-EMERGENCY COMBINED DRAIN

LORO-X Bend - Pipe in pipe -
Degree	DN 100
87°	13530.100X
70°	13531.100X
45°	13532.100X
30°	13533.100X
15°	13534.100X